Mitee-Bite Products Inc., a supplier of precision workholding equipment, has introduced the #9 ID Xpansion fixture, a low-profile device intended for internal-diameter clamping on vertical machining centers and other machine tool applications. According to the company, the fixture is designed to address concentricity and rigidity challenges that arise when a workpiece must be held from its bore rather than its exterior.
The #9 ID Xpansion is built for workholding from an internal diameter. Before use, the fixture can be precision-turned to match a specific workpiece, allowing it to fit closely inside the bore. Mitee-Bite says that custom fit can yield concentricity as tight as 0.0005 inch (0.0127 millimeter).
The fixture retains the compact, low-profile format of the ID Xpansion series. Its flange diameter is the same as that of the #8 model, a design choice intended to support accurate installation when fixtures are packed densely on multi-station setups such as Workcube systems or fixture plates.
The shared flange diameter is intended to allow high-density arrangements without sacrificing installation accuracy. Mitee-Bite says this makes the fixture suitable for multi-station machining environments, including Workcube systems and fixture plates.
The standardized flange also permits operators to position and change multiple parts on a vertical machining center with relative speed, according to the company, supporting production efficiency.
| Parameter | Specification |
|---|---|
| Maximum internal-diameter clamping size | 6.89 in (175 mm) |
| Minimum turnable diameter | 1.15 in (29.21 mm) |
| Concentricity | 0.0005 in (0.0127 mm) |
| Mounting | Hex wrench or hydraulic drawbar cylinder |
For heavier cutting operations, the #9 ID Xpansion uses a through-screw design. The screw has a tapered head and passes directly through the fixture body to lock into a fixture plate or hydraulic drawbar cylinder.
That direct connection is intended to increase the overall rigidity of the workholding system, reduce vibration during machining and support stable cutting of complex parts, the company says.
The fixture can be installed with a hex wrench or a hydraulic drawbar cylinder, according to the specifications. It is positioned for both single-part work and higher-volume setups in which several parts are located and exchanged on a vertical machining center.
Mitee-Bite Products Inc., a supplier of precision workholding equipment, has introduced the #9 ID Xpansion fixture, a low-profile device intended for internal-diameter clamping on vertical machining centers and other machine tool applications. According to the company, the fixture is designed to address concentricity and rigidity challenges that arise when a workpiece must be held from its bore rather than its exterior.
The #9 ID Xpansion is built for workholding from an internal diameter. Before use, the fixture can be precision-turned to match a specific workpiece, allowing it to fit closely inside the bore. Mitee-Bite says that custom fit can yield concentricity as tight as 0.0005 inch (0.0127 millimeter).
The fixture retains the compact, low-profile format of the ID Xpansion series. Its flange diameter is the same as that of the #8 model, a design choice intended to support accurate installation when fixtures are packed densely on multi-station setups such as Workcube systems or fixture plates.
The shared flange diameter is intended to allow high-density arrangements without sacrificing installation accuracy. Mitee-Bite says this makes the fixture suitable for multi-station machining environments, including Workcube systems and fixture plates.
The standardized flange also permits operators to position and change multiple parts on a vertical machining center with relative speed, according to the company, supporting production efficiency.
| Parameter | Specification |
|---|---|
| Maximum internal-diameter clamping size | 6.89 in (175 mm) |
| Minimum turnable diameter | 1.15 in (29.21 mm) |
| Concentricity | 0.0005 in (0.0127 mm) |
| Mounting | Hex wrench or hydraulic drawbar cylinder |
For heavier cutting operations, the #9 ID Xpansion uses a through-screw design. The screw has a tapered head and passes directly through the fixture body to lock into a fixture plate or hydraulic drawbar cylinder.
That direct connection is intended to increase the overall rigidity of the workholding system, reduce vibration during machining and support stable cutting of complex parts, the company says.
The fixture can be installed with a hex wrench or a hydraulic drawbar cylinder, according to the specifications. It is positioned for both single-part work and higher-volume setups in which several parts are located and exchanged on a vertical machining center.