The IT-KTD-30 end clamp is a photovoltaic mounting component engineered to secure solar modules to support structures with a 30 mm top width. The device uses a mechanical locking design intended to maintain structural stability under wind loads. Its aluminum construction and anodized finish are specified for outdoor solar installations.
In photovoltaic bracket systems, end clamps serve as critical connection points that hold module frames in place. The IT-KTD-30 is designed specifically for support structures with a 30 mm top surface width, applying precise physical locking to help preserve module alignment and structural integrity under wind loading.
The end clamp is made from A6005-T6 aluminum alloy and receives an anodized treatment for weather resistance. The following table lists the product's detailed specifications.
| Parameter | Specification |
|---|---|
| Model | IT-KTD-30 |
| Dimensions | L54 x W68 x H50 mm (±3%) |
| Material | A6005-T6 (anodized, HV>85) |
| Fastener | M5.5 x 25 mm stainless steel 304 screws (4 pieces) |
| Application | 30 mm wide top surface bracket/rail |
The component is primarily matched with the IT-TR-2850 rail and is also compatible with other general rails that meet the required dimensions. The A6005-T6 aluminum alloy, combined with anodizing at a hardness above HV 85, is intended to provide oxidation resistance and corrosion resistance in most outdoor photovoltaic environments.
The stainless steel 304 fasteners are supplied as four M5.5 x 25 mm screws. Installers are advised to verify that the clamp-to-module-frame contact surface is flat before tightening.
During installation, the clamp must be checked for proper contact with the module frame. The stainless steel screws should be tightened to the torque specified by the overall bracket system design, avoiding over- or under-tightening that could cause uneven stress on the module.
The product is not universally compatible with all photovoltaic brackets. Before use, the top surface width of the rail must be confirmed to match the 30 mm design requirement.
The IT-KTD-30 end clamp is a photovoltaic mounting component engineered to secure solar modules to support structures with a 30 mm top width. The device uses a mechanical locking design intended to maintain structural stability under wind loads. Its aluminum construction and anodized finish are specified for outdoor solar installations.
In photovoltaic bracket systems, end clamps serve as critical connection points that hold module frames in place. The IT-KTD-30 is designed specifically for support structures with a 30 mm top surface width, applying precise physical locking to help preserve module alignment and structural integrity under wind loading.
The end clamp is made from A6005-T6 aluminum alloy and receives an anodized treatment for weather resistance. The following table lists the product's detailed specifications.
| Parameter | Specification |
|---|---|
| Model | IT-KTD-30 |
| Dimensions | L54 x W68 x H50 mm (±3%) |
| Material | A6005-T6 (anodized, HV>85) |
| Fastener | M5.5 x 25 mm stainless steel 304 screws (4 pieces) |
| Application | 30 mm wide top surface bracket/rail |
The component is primarily matched with the IT-TR-2850 rail and is also compatible with other general rails that meet the required dimensions. The A6005-T6 aluminum alloy, combined with anodizing at a hardness above HV 85, is intended to provide oxidation resistance and corrosion resistance in most outdoor photovoltaic environments.
The stainless steel 304 fasteners are supplied as four M5.5 x 25 mm screws. Installers are advised to verify that the clamp-to-module-frame contact surface is flat before tightening.
During installation, the clamp must be checked for proper contact with the module frame. The stainless steel screws should be tightened to the torque specified by the overall bracket system design, avoiding over- or under-tightening that could cause uneven stress on the module.
The product is not universally compatible with all photovoltaic brackets. Before use, the top surface width of the rail must be confirmed to match the 30 mm design requirement.