logo
บล็อก
blog details
บ้าน > บล็อก >
ITKTD30 Solar End Clamps Technical Specs and Selection Guide
กิจกรรม
ติดต่อเรา
Mr. Sun Shuai
86-023-62818056
ติดต่อตอนนี้

ITKTD30 Solar End Clamps Technical Specs and Selection Guide

2026-10-31
Latest company blogs about ITKTD30 Solar End Clamps Technical Specs and Selection Guide

The IT-KTD-30 end clamp is a photovoltaic mounting component engineered to secure solar modules to support structures with a 30 mm top width. The device uses a mechanical locking design intended to maintain structural stability under wind loads. Its aluminum construction and anodized finish are specified for outdoor solar installations.

Product overview

In photovoltaic bracket systems, end clamps serve as critical connection points that hold module frames in place. The IT-KTD-30 is designed specifically for support structures with a 30 mm top surface width, applying precise physical locking to help preserve module alignment and structural integrity under wind loading.

Core technical specifications

The end clamp is made from A6005-T6 aluminum alloy and receives an anodized treatment for weather resistance. The following table lists the product's detailed specifications.

Parameter Specification
Model IT-KTD-30
Dimensions L54 x W68 x H50 mm (±3%)
Material A6005-T6 (anodized, HV>85)
Fastener M5.5 x 25 mm stainless steel 304 screws (4 pieces)
Application 30 mm wide top surface bracket/rail
Compatibility and material performance

The component is primarily matched with the IT-TR-2850 rail and is also compatible with other general rails that meet the required dimensions. The A6005-T6 aluminum alloy, combined with anodizing at a hardness above HV 85, is intended to provide oxidation resistance and corrosion resistance in most outdoor photovoltaic environments.

The stainless steel 304 fasteners are supplied as four M5.5 x 25 mm screws. Installers are advised to verify that the clamp-to-module-frame contact surface is flat before tightening.

Selection and installation guidance

During installation, the clamp must be checked for proper contact with the module frame. The stainless steel screws should be tightened to the torque specified by the overall bracket system design, avoiding over- or under-tightening that could cause uneven stress on the module.

The product is not universally compatible with all photovoltaic brackets. Before use, the top surface width of the rail must be confirmed to match the 30 mm design requirement.

Frequently Asked Questions
Is the IT-KTD-30 end clamp suitable for all photovoltaic mounting systems?
No. The model is designed specifically for brackets with a 30 mm top width. Users must confirm that the top surface width of their rail matches this specification before installation.
How does the product's material perform in terms of corrosion resistance?
The clamp uses A6005-T6 aluminum alloy with anodized treatment at a hardness above HV 85. This provides strong oxidation and corrosion resistance for most outdoor photovoltaic environments.
What fastening details should be observed during installation?
The clamp requires the supplied M5.5 x 25 mm stainless steel 304 screws. Installers should check the engagement between the screws and the rail slot and ensure even force distribution.
บล็อก
blog details
ITKTD30 Solar End Clamps Technical Specs and Selection Guide
2026-10-31
Latest company news about ITKTD30 Solar End Clamps Technical Specs and Selection Guide

The IT-KTD-30 end clamp is a photovoltaic mounting component engineered to secure solar modules to support structures with a 30 mm top width. The device uses a mechanical locking design intended to maintain structural stability under wind loads. Its aluminum construction and anodized finish are specified for outdoor solar installations.

Product overview

In photovoltaic bracket systems, end clamps serve as critical connection points that hold module frames in place. The IT-KTD-30 is designed specifically for support structures with a 30 mm top surface width, applying precise physical locking to help preserve module alignment and structural integrity under wind loading.

Core technical specifications

The end clamp is made from A6005-T6 aluminum alloy and receives an anodized treatment for weather resistance. The following table lists the product's detailed specifications.

Parameter Specification
Model IT-KTD-30
Dimensions L54 x W68 x H50 mm (±3%)
Material A6005-T6 (anodized, HV>85)
Fastener M5.5 x 25 mm stainless steel 304 screws (4 pieces)
Application 30 mm wide top surface bracket/rail
Compatibility and material performance

The component is primarily matched with the IT-TR-2850 rail and is also compatible with other general rails that meet the required dimensions. The A6005-T6 aluminum alloy, combined with anodizing at a hardness above HV 85, is intended to provide oxidation resistance and corrosion resistance in most outdoor photovoltaic environments.

The stainless steel 304 fasteners are supplied as four M5.5 x 25 mm screws. Installers are advised to verify that the clamp-to-module-frame contact surface is flat before tightening.

Selection and installation guidance

During installation, the clamp must be checked for proper contact with the module frame. The stainless steel screws should be tightened to the torque specified by the overall bracket system design, avoiding over- or under-tightening that could cause uneven stress on the module.

The product is not universally compatible with all photovoltaic brackets. Before use, the top surface width of the rail must be confirmed to match the 30 mm design requirement.

Frequently Asked Questions
Is the IT-KTD-30 end clamp suitable for all photovoltaic mounting systems?
No. The model is designed specifically for brackets with a 30 mm top width. Users must confirm that the top surface width of their rail matches this specification before installation.
How does the product's material perform in terms of corrosion resistance?
The clamp uses A6005-T6 aluminum alloy with anodized treatment at a hardness above HV 85. This provides strong oxidation and corrosion resistance for most outdoor photovoltaic environments.
What fastening details should be observed during installation?
The clamp requires the supplied M5.5 x 25 mm stainless steel 304 screws. Installers should check the engagement between the screws and the rail slot and ensure even force distribution.